防爆加熱管是一種消耗電能轉換為熱能，來對需加熱物料進行加熱。防爆加熱管是由外到里外殼（不繡鋼/碳鋼/銅/鈦材等、發熱絲（鎳鉻鉛合金）、填充物（氧化鎂，作用是導熱、絕緣）、外殼（不繡鋼、碳鋼、鈦材、銅  等）、陶瓷封頭（作用：絕緣）、防爆盒組成的。加熱管在工作中低溫流體介質通過管道在壓力作用下進入其輸入口，沿著電加熱容器內部特定換熱流道，運用空氣電熱管的流體熱力學原理設計的路徑，帶走空氣加熱管中的電熱元件工作中所產生的高溫熱能量，使空氣加熱管被加熱介質溫度升高，加熱管出口得到工藝要求的高溫介質。

產品特點

1.升溫時間在試驗電壓下，元件從環境溫度升至試驗溫度時間應不大于15min

2.額(e)(e)定功率偏差在充分發熱的條件下，元件的額(e)(e)定功率的偏差應不超過下列規定的范圍;對額(e)(e)定功率小于等于100W的元件為:士10%。對額(e)(e)定功率大于100W的元件為+5%~- 10%或10W,取兩者中的較大值。

3.泄露電流冷態泄露電流以及水壓和密封試驗后泄露電流應不超過0.5mA工作溫度下的熱態泄露電流應不超過公式中的計算值，但不超過5mA I=1/6 (tTX0.00001) I一 熱態泄露電流mA t-發熱長度mm T-工作溫度C多個元件串聯到電源中時，應以這一組元件為 整體進行泄露電流試驗。

4. 絕緣電阻出廠檢驗時冷態絕緣電阻應不小于50MQ密封試驗后，長期存放或者使用后的絕緣電阻應不消與MQ工作溫度下的熱態絕緣電阻應不低于公式中的計算值，但應不小于1MQ R=「(10-0.015T) /t」X0.001 R熱態絕緣電阻MQ t一-發 熱長度mmT一工作溫度°C

5.絕緣耐壓強度元件應在規定的試驗條件和試驗電壓下保持1min,而無閃絡和擊穿現象

6.經受通斷電的能力元件應能在規定的試驗條件下經歷2000次通斷電試驗，而不發生損壞